Centrifugal Cast And Shotcrete Applied Material

Forum rules
NO SPAM

by safzxbv111 » Fri Mar 15, 2019 2:01 am

PRODUCT DESCRIPTION
Tasir ® Centrifugal Cast Water Stop is a fast-setting hydraulic cement that stops active leaks in concrete. Easy to apply, Tasir ® Centrifugal Cast Water Stop is high-bond and high-strength and is resistant to oil, gas, salt water, and sulphates. This product is recommended for active leaks or flowing water and can be applied on new or existing concrete, mortar, brick, or any other surface to which cementitious products can bond.
ADVANTAGES
● Completely Waterproof
● Rapid Setting & Permanent
● Single Component
● Easy-to-Apply
● Oil, Gas, Saltwater, and Sulfate Resistant
● High Bond Strength
USES
● Plugging water leaks/seepage in concrete, stone, or other surfaces to which cementitious products can bond
● Crack filler material for active leaks
PACKAGING AND YIELD
Tasir ® Centrifugal Cast Water Stop is packaged in an 10 lb. pail yielding about 145 in3 (2.4 liters).
SHELF LIFE
One year in original unopened container when stored in clean, dry area at 70°F (21°C).
TYPICAL PROPERTIES AT 70°F (21°C)
UsageOpen Air or Underwater
Working Time at 70°F (21°C)3 - 5 minutes
Initial Set Time at 70°F (21°C) ASTM C 1093 - 5 minutes
Final Set Time at 70°F (21°C) ASTM C 1095 - 10 minutes
Compressive Strength, ASTM C 109
3 Hours1,500 psi (10.3 MPa)
1 Day2,500 psi (17.2 MPa)
28 Days4,000 psi (27.5 MPa)
The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result. Test methods are modified where applicable.

PLACEMENT GUIDELINES
1. SURFACE PREPARATION: All horizontal and vertical concrete surfaces in contact with Tasir ® Centrifugal Cast Water Stop shall be sound and free of oil, grease, laitance, and other contaminants. Open cracks or holes by cutting back to a minimum depth of 1 inch (25 mm) to sound material. Cut back to a square or dovetail joint, do not use a “V” cut. Remove all contaminated and loose material. Pre- soak surface with clean water prior to placement.
2. MIXING: Condition Tasir ® Centrifugal Cast Water Stop to 70°F (21°C). Mix with warm, clean water to a stiff consistency that can be formed into a ball without crumbling and retains its shape when squeezed. When working conditions are under 40°F (4°C), Tasir ® Centrifugal Cast Water Stop will have a slower set than normal. For hot weather working conditions, it is recommended that cool or iced water be used to slow set to the desired rate. Do not mix more Tasir ® Centrifugal Cast Water Stop than can be placed in 3 minutes.
3. PLACEMENT PROCEDURES: With gloved hand, form a plug and force into the crack or hole with maximum pressure.
4. POST-PLACEMENT PROCEDURES: For cracks or holes with considerable water pressure, use temporary bracing or framework to hold Tasir ® Centrifugal Cast Water Stop until material fully reaches set and can withstand water pressure.
NOTE: PRIOR TO APPLICATION, READ ALL PRODUCT PACKAGING THOROUGHLY. For more detailed placement procedures, refer to Tasir installation guidelines or call Tasir Products’ Engineering and Technical Service Center at 1-800-243-2206.
CAUTION
Contains cementitious material and crystalline silica. International Agency for Research on Cancer has determined that there is sufficient evidence for the carcinogenicity of inhaled crystalline silica to humans. Take appropriate measures to avoid breathing dust. Avoid contact with eyes and contact with skin. In case of contact with eyes, immediately flush with plenty of water for at least 15 minutes. Immediately call a physician. Wash skin thoroughly after handling. Keep product out of reach of children. PRIOR TO USE, REFER TO SAFETY DATA SHEET.
For worldwide availability, additional product information and technical support, contact your local sales representative, or call Tasir
Products'Engineering and Technical Service Center at 1-800-243-2206.
SKU / PRODUCT CODE DESCRIPTION #UNITS/PALLET UNIT SIZE
CCWSTasir ® Centrifugal Cast Water Stop4810 lb. (4.5 kg) Pail
WARRANTY: “Tasir PRODUCTS ARE MANUFACTURED TO BE FREE OF MANUFACTURING DEFECTS AND TO MEET FSP'S CURRENT PUBLISHED PHYSICAL PROPERTIES WHEN APPLIED IN ACCORDANCE WITH Tasir'S DIRECTIONS AND TESTED IN ACCORDANCE WITH ASTM AND Tasir STANDARDS. HOWEVER, SHOULD THERE BE DEFECTS OF MANUFACTURING OF ANY KIND, THE SOLE RIGHT OF THE USER WILL BE TO RETURN ALL MATERIALS ALLEGED TO BE DEFECTIVE, FREIGHT PREPAID TO Tasir, FOR REPLACEMENT. THERE ARE NO OTHER WARRANTIES BY Tasir OF ANY NATURE WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH THIS PRODUCT. Tasir SHALL NOT BE LIABLE FOR DAMAGES OF ANY SORT, INCLUDING PUNITIVE, ACTUAL, REMOTE, OR CONSEQUENTIAL DAMAGES, RESULTING FROM ANY CLAIMS OF BREACH OF CONTRACT, BREACH OF ANY WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR FROM ANY OTHER CAUSE WHATSOEVER. Tasir SHALL ALSO NOT BE RESPONSIBLE FOR USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT HELD BY OTHERS.”
Tasir Construction Material&Technology Corporate Headquarters
Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China
Specifications Subject to Change.
For most current version of datasheet, go to groutmaterial.com
© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated
• Tel: +86-571-28119206
• Fax: +86-571-28197878
groutmaterial.comCentrifugal Cast And Shotcrete Applied Material
website:http://www.groutmaterial.com/centrifugal-cast-and-shotcrete-applied-material/
safzxbv111
 
Posts: 11
Joined: Fri Mar 15, 2019 1:55 am

Return to Jewelry Discussion